Hansenbrygg skrev:
Hansenbrygg skrev:
Hansenbrygg skrev:
Ny Pi - Kjør disse
sudo apt-get update
sudo apt-get upgrade
sudo raspi-config
--
Apache Server:
sudo apt-get install apache2 php5 libapache2-mod-php5
sudo service apache2 restart
--
WebMin
sudo nano /etc/apt/sources.list
kopier inn følgende to linjer under eksisterende(avslutt med ctrl+X og Y):
deb [url]http://download.webmin.com/download/repository [/url]sarge contrib
deb [url]http://webmin.mirror.somersettechsolutions.co.uk/repository [/url]sarge contrib
cd /
sudo wget [url]http://www.webmin.com/jcameron-key.asc
[/url]sudo apt-key add jcameron-key.asc
sudo apt-get update
sudo apt-get install webmin
--
Statisk IP
Statisk IP, kjør og editer:
sudo nano /etc/network/interfaces
kopier inn følgende og endre til dine ip verdier
auto lo
iface lo inet loopback
iface eth0 inet static
address 192.168.0.200
netmask 255.255.255.0
gateway 192.168.0.1
allow-hotplug wlan0
iface wlan0 inet manual
wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
iface default inet dhcp
--
Klargjøre linuxkjerne for Temp Sensor DS18B20
kople sensor slik: [url]http://www.sbprojects.com/projects/raspberrypi/ds1820connect.png
[/url]sudo modprobe w1_gpio && sudo modprobe w1_therm
sudo sh -c "echo 'w1_gpio\nw1_therm\n' >> /etc/modules"
Installering av RasBrew
Klaggjør som over minimum apache
Temp på +1, gnd,pinne 6, data pinne 7
SSR gnd pinne 6, + pinne 11
sudo apt-get install python-setuptools
sudo easy_install -U pyserial
sudo apt-get install python-smbus
sudo easy_install web.py
Last ned sw herifra:
[url]https://github.com/steve71/RasPiBrew [/url]
og legg inn på web root(gjerne via webmin)
Editer config.xml Sensorkode og C(via webmin)
Test om temp leses via termnal(bytt ut med din 28-kode):
cat /sys/bus/w1/devices/28-0000046ede5a/w1_slave
Sett kataloger (web root) til 755 web (gjerne via webmin)
sudo bash
cd /var/www
nano /etc/init.d/raspibrew
Kopier inn teksten hele teksten under til neste --
#! /bin/sh
# /etc/init.d/raspibrew
### BEGIN INIT INFO
# Provides: raspibrew
# Required-Start: $remote_fs $syslog
# Required-Stop: $remote_fs $syslog
# Default-Start: 2 3 4 5
# Default-Stop: 0 1 6
# Short-Description: Simple script to start a program at boot
# Description: A simple script from www.stuffaboutcode.com which will start / st$
### END INIT INFO
# If you want a command to always run, put it here
# Carry out specific functions when asked to by the system
case "$1" in
start)
echo "Starting RasPiBrew"
# run application you want to start
python /var/www/raspibrew.py
;;
stop)
echo "Stopping RasPiBrew"
# kill application you want to stop
killall python
python /var/www/cleanupGPIO.py
;;
*)
echo "Usage: /etc/init.d/raspibrew {start|stop}"
exit 1
;;
esac
exit 0
--
sudo chmod 755 /etc/init.d/raspibrew
sudo update-rc.d raspibrew defaults
sudo /etc/init.d/raspibrew start
Logg på med webbrowser i.p.n.r:8080
Hans Einar skrev:
Koden ligger i template katalogen.. :yes: Streva litt med å få klokka bra. Verdiene for den er slik nå(ca rundt linje 300):
//draw gauge
var options_gauge = {
majorTickLabel: true,
value: 65,
label: 'Temp',
unitsLabel: '' + String.fromCharCode(186),
min: 0,
max: 100,
majorTicks: 21,
minorTicks: 4, // small ticks inside each major tick
greenFrom: 62,
greenTo: 68,
yellowFrom: 45,
yellowTo: 62,
redFrom: 68,
redTo: 100
};#! /bin/sh
# /etc/init.d/raspibrew
### BEGIN INIT INFO
# Provides: raspibrew
# Required-Start: $remote_fs $syslog
# Required-Stop: $remote_fs $syslog
# Default-Start: 2 3 4 5
# Default-Stop: 0 1 6
# Short-Description: Simple script to start a program at boot
# Description: A simple script from www.stuffaboutcode.com which will start / st$
### END INIT INFO
# If you want a command to always run, put it here
# Carry out specific functions when asked to by the system
case "$1" in
start)
echo "Starting RasPiBrew"
# run application you want to start
python /var/www/raspibrew.py
;;
stop)
echo "Stopping RasPiBrew"
# kill application you want to stop
killall python
python /var/www/cleanupGPIO.py
;;
*)
echo "Usage: /etc/init.d/raspibrew {start|stop}"
exit 1
;;
esac
exit 0ps aux |grep raspibrew.py | awk '{print $2}'| xargs killOddvar Demmo skrev:
Hansenbrygg skrev:
senkes spenningen senkes strømmen, i dette tilfellen er den senket nesten til 1/4 så da senkes strømmen til 1/4, trust me i know.runeni skrev:
