• Bruk prefiks-funksjonen når du oppretter nye poster i dette forumet.

Til Salgs Grain roller crusher/grinder

Har vært i kontakt med selger. Han sender ikke utenfor Polen, pga manglende registrering i ett eller annet polsk register. Han sier det kommer til å endre seg i løpet av et halvt års tid - frem til det er løsningen å få noen til å videresende fra Polen.

Da krysser jeg fingrene for at de får til shipping.
Det ser ut til å være et bra produkt!
 
Har vært i kontakt med selger. Han sender ikke utenfor Polen, pga manglende registrering i ett eller annet polsk register. Han sier det kommer til å endre seg i løpet av et halvt års tid - frem til det er løsningen å få noen til å videresende fra Polen.
Jeg har en kompis som kan ta imot og videresende til meg. Si ifra om noen er interessert
 
hva er diameter på valsene? Hvis noennhadde videresent for meg så er det jo interessant, den mølla jeg vil ha koster jo over det dobbelte.. Men noen som vet/kan måle dia på valsene?
 
hva er diameter på valsene? Hvis noennhadde videresent for meg så er det jo interessant, den mølla jeg vil ha koster jo over det dobbelte.. Men noen som vet/kan måle dia på valsene?
Dette er google translated fra salgsannonsen jeg har linket.

Device structure:
- gap adjustment between rolls in the range of 0.5-3.5 mm
- shafts embedded in the housing on bearings.
- rings on rollers are made of high quality abrasion resistant steel with hardness of about 50 HRC (twice as hard as AISI 304 stainless steel often used by manufacturers, similar hardness as hardened C45 steel also used in production of grinding rollers)
- roll length 80 mm, diameter 40 mm made of 4 mm thick rings
- grinding with a screwdriver or drill
(not included)
- drive shaft shafts milled in a hexagon which provides a strong handle of the screwdriver head
- stainless steel hopper with a capacity of about 3 kg
- the weight of the razor is about 5 kg which ensures stable operation of the device.
 
Dette er google translated fra salgsannonsen jeg har linket.

Device structure:
- gap adjustment between rolls in the range of 0.5-3.5 mm
- shafts embedded in the housing on bearings.
- rings on rollers are made of high quality abrasion resistant steel with hardness of about 50 HRC (twice as hard as AISI 304 stainless steel often used by manufacturers, similar hardness as hardened C45 steel also used in production of grinding rollers)
- roll length 80 mm, diameter 40 mm made of 4 mm thick rings
- grinding with a screwdriver or drill
(not included)
- drive shaft shafts milled in a hexagon which provides a strong handle of the screwdriver head
- stainless steel hopper with a capacity of about 3 kg
- the weight of the razor is about 5 kg which ensures stable operation of the device.
Aha. Takk. Alt ser mye større ut på bilder. Da blir det nok fortsatt den andre.
 
Jeg har en kompis som kan ta imot og videresende til meg. Si ifra om noen er interessert
Det hadde jo vært supert. Jeg er interessert i en med drift på begge valser. Litt avhengig av hva totalprisen blir, selvfølgelig.

Sent fra min CLT-L29 via Tapatalk
 
Hei, I was in contact with a friend who is making them and we discussed a bit and I think I would be able to import few with another friend who is travelling often. If there would be few people interested we can move forward with this. Transport would be around 500-600NOK from poland divided to each mill depends of how many people want it. Then you can pick it up in Oslo or I would be able to send via postnord which is the cheapest I think now. Let me know if anyone would be interested.
 
Hei, I was in contact with a friend who is making them and we discussed a bit and I think I would be able to import few with another friend who is travelling often. If there would be few people interested we can move forward with this. Transport would be around 500-600NOK from poland divided to each mill depends of how many people want it. Then you can pick it up in Oslo or I would be able to send via postnord which is the cheapest I think now. Let me know if anyone would be interested.
As I mentioned to Harps, I am interested in one with gears. Maybe two. I can arrange pickup in Oslo.

Sent fra min CLT-L29 via Tapatalk
 
Hei, I was in contact with a friend who is making them and we discussed a bit and I think I would be able to import few with another friend who is travelling often. If there would be few people interested we can move forward with this. Transport would be around 500-600NOK from poland divided to each mill depends of how many people want it. Then you can pick it up in Oslo or I would be able to send via postnord which is the cheapest I think now. Let me know if anyone would be interested.
Hello There. I see it's a while since you asked, but I ask anyway. Is it possible to buy one?
 
Tilbake
Topp